Photography

Photos from the blog. Select a photo to read the post.

Titan LSD Rebuild 2026 ↗A new generation 2026 ↗Brake pressure sensor 2017 ↗Front suspension travel sensors 2017 ↗Airbox static flow CFD analysis 2017 ↗Cool spark plugs 2017 ↗DIY Duratec balance shaft delete 2016 ↗VCT Delete 2016 ↗Duratec Front Pulleys 2016 ↗Damper position sensors 2016 ↗Penske dampers 2016 ↗Pushrod strain gauges 2015 ↗New LSD from Titan 2015 ↗Rear wheel bearings 2015 ↗Unsprung weight 2015 ↗3D printed GoPro mount 2015 ↗Bronze bushing 2015 ↗3D-printed moulds for polyurethane bushes 2015 ↗Bad earth troubleshooting 2015 ↗Custom moulded ear plugs 2015 ↗3D printed cold air intake 2015 ↗Rear bump steer 2015 ↗Airfoil behind roll cage CFD analysis 2015 ↗Engine bay undertray aerodynamics 2014 ↗MOT, autumn and nothing much 2014 ↗My wheel fell off on a trackday 2014 ↗New rims with stickers on 2014 ↗Gearbox disaster 2014 ↗TimeAttack - "King of Mantorp" 2014 ↗Intake cone filter and air pressure 2014 ↗Attempt to redirect exhaust noise 2014 ↗Intake airbox 2014 ↗Raceco silencer 2014 ↗Rear diffusor and front splitter inspiration 2014 ↗Aerodynamics - CFD simulations 2014 ↗Fuel system with Swirlpot 2014 ↗Oil filler cap lock 2014 ↗Oil temperature sender 2014 ↗Race Technology DL1 + Dash4Pro 2013 ↗Fuel filter 2013 ↗Uprated fuel pump 2013 ↗Tierp Arena 2013 ↗Finally some driving!! 2013 ↗Brise starter 2013 ↗Head job 2013 ↗Engine rebuilt 2013 ↗New engine block 2013 ↗New engine loom 2013 ↗Cranks and rpm limit 2013 ↗Engine damage 2013 ↗Mantorp first time 2013 2013 ↗Cornerweight, for real 2013 ↗Nose cone aero whiskers 2013 ↗Exhaust manifold leak 2013 ↗DIY Cornerweight 2013 ↗Full rollcage 2013 ↗Oil catch tank 2013 ↗Front damper spherical bearing play 2013 ↗Replacing front bushings 2013 ↗Front cover oil leak 2012 ↗Dry sump blanking cap 2012 ↗Gelleråsen end of season 2012 ↗Mantorp wear and tear 2012 ↗Exhaust gasket leak 2012 ↗Min Stora Dag charity event 2012 ↗Yearly MOT - No problems, no worries! 2012 ↗Progress 2012 ↗Mantorp - slicks vs CR500 2012 ↗OptimumLap simulation software 2012 ↗Mantorp and two new sets of slicks 2012 ↗Fuel injector voltage compensation 2012 ↗Inertial switch 2012 ↗New exhaust primaries and collector 2012 ↗Wideband lambda 2012 ↗Flat tyre 2012 ↗Air temp sender location 2012 ↗Trackday slicks part #4 - how did it go? 2012 ↗Mantorp graduation 2012 ↗Camber calculator 2012 ↗Rear hub nuts 2012 ↗Engine upgrade - part #9 - final results 2012 ↗Engine upgrade - part #8 - first start!!! 2012 ↗Engine upgrade - part #7 - electrical and fuel 2012 ↗Engine upgrade - part #6 - putting it together 2012 ↗Engine upgrade - part #5 - head 2012 ↗Engine upgrade - part #4 - block assembly 2012 ↗Engine upgrade - part #3 - parts 2012 ↗Engine upgrade - part #2 - disassemble 2011 ↗Engine upgrade - part #1 - intro 2011 ↗CSR Assembly Guide and other manuals 2011 ↗Trackday slicks part #3 - Fitting 13" rims 2011 ↗Supercharged! 2011 ↗Mantorp, last time this year 2011 ↗MOT test 2011 ↗Adjusting Camber 2011 ↗Gotland Ring 2011 ↗Limited rear droop travel 2011 ↗Cracked exhaust manifold 2011 ↗The engine is out 2011 ↗